AIRx 12.5x20x5HW-HEALTH | Our#: 202707
12.5x20x5 AIRx ALLERGY Honeywell FC100A1052 Replacement Air Filter - MERV 13, 2-Pack
AIRx 12.5x20x5HW-HEALTH | Our#: 202707
- Free Shipping & Free Returns
- 100% Compatibility Guarantee
Protect more sensitive lungs
- Highest rated filter to reduce most pollutants
- Reduces pollen, dust, lint, dust mite debris, pet dander & mold spores
- Lessens odors from car fumes & smoke
- Removes bacteria & virus carriers
- Creates cleaner indoor air
- Actual Dimensions: 12 ⅜" x 19 ⅞" x 4 ⅜"
2 people in your area recently purchased this product!
$29.90
$37.38 Save 20%
(2 Filters for $59.80)
Your Discount: DF20
In Stock
Ships in 24 hours
Frequently Purchased Together-
- Free Shipping & Free Returns
- 100% Compatibility Guarantee
Frequently Purchased Together
Frequently Purchased Together
12.5x20x5 AIRx ALLERGY Honeywell FC100A1052 Replacement Air Filter - MERV 8, 2-Pack
(case of 2 Filters) MFG#: 12.5x20x5HW-DUST
$62.25
Product Details
This aftermarket filter replaces the original Honeywell part number FC100A1052. 12.5" X 20" X 5" MERV 13 Filter. (Actual Dimensions - 12 1/2" X 20" X 4-3/8"). Highly-efficient, synthetic material features extended surface pleats that have a higher dirt-holding capacity than competitive filters. These high quality filters capture and hold pollutants inside the filter, allowing clean air to flow freely through the system.
FEATURES:
- Value-priced replacement for expensive original factory part
- Moisture resistant frame remains sturdy even in high humidity
- Rust resistant galvanized wire downstream gives the filter rigidity and holds media in place after installation
- Built-in support fingers hold pleats in place and allow for maximum dust holding
- For optimum system performance, replace the filter every six months
- MERV 13 rating means the filter attracts and captures more than 90% of particles from 1-3 microns in sizeld spores as well as smaller particulate
Do you want to know about the technical specs?
Nominal Dimensions
12 ½ x 20 x 5"
Actual Dimensions
12 ⅜ x 19 ⅞ x 4 ⅜"
Filter Media
Electrostatically charged 100% synthetic gradient media that does not support microbiological growth
Filter Support Grid
30 gauge galvanized expanded metal grid
Frame
Moisture resistant double-wall beverage board
Max Temperature
180F (82C) continuous service, peak 225F (107C)
Max Humidity
Resistant to 100% R.H.
Replaces These Filters:
Accumulair:
DPFW12.5X20X5
Honeywell:
203372
FC100A1052
National Filter Sales:
12.5x20x4
12.5x20x5
How to change your furnace/air-conditioner/HVAC air filter
Estimated time: 10 minutes or less
Steps
Determine the location of your filter
Your forced air system will be similar, whether or not it is a heating (furnace) or cooling (AC) system – or both. The furnace filter housing/slot is located right next to the heating/cooling system’s air handler or blower. Your filter(s) may also be located in a return grille on the wall or ceiling of your home.
Determine the type/size of filter that you use
Typically, the dimensions or part number of the filter will be printed on the filter frame. Use this information to order a new filter.
Purchase a new air filter from DiscountFilters.com
Visit DiscountFilters.com and purchase a new filter. Use our filter finders to verify the correct match.
Remove the old filter
Turn off the power to the heating/cooling system and remove the old filter from its housing/slot and discard.
Insert the new filter
Pay attention to any airflow direction arrows printed on the frame of the new filter. Install the filter by sliding it into the filter housing/slot with the airflow arrow pointing towards the blower. If installing the filter in a wall or ceiling grille – the airflow arrow should point towards the wall or ceiling. Turn on the power to the forced air system.
Enjoy cleaner air!